* * * * * * * * * * * * * * * * S-69 * * * * * * * * * * * * * * *

PRODUCT DESCRIPTION: Proprietary water-based corrosion inhibitor coating.

Carcinogenic: OSHA = no NTP = no IARC = no

COLOR: Amber PHYSICAL FORM: Liquid

NON-VOLATILE (weight): 45-50% MELTING RANGE: N.A.

ODOR: Slightly ammoniacal pH: 8.5-9.5 (1% in water)

FREEZING POINT: N.E. BOILING RANGE: N.E.

VAPOR DENSITY: N.E. VAPOR PRESSURE: N.E.

EVAPORATION RATE: N.E.

DENSITY: 9.4-9.5 lb/gal (1.13-1.14 kg/l)

HMIS FLAMMABILITY RATING: 0

FLASH POINT: >200ºF (93ºC)

FLAMMABLE LIMITS: LEL: N.E. UEL: N.E.

EXTINGUISHING MEDIA: Water, carbon dioxide, foam, or other dry chemical fire fighting agents.

UNUSUAL FIRE AND EXPLOSION HAZARDS: None

SPECIAL FIRE FIGHTING PROCEDURES: Firefighters should wear self-contained breathing apparatus.

EMERGENCY AND FIRST AID PROCEDURES:

Eye Contact: Flush eyes with water for at least 15 minutes. If the material is not easily flushed from the eye, rinse with USP mineral oil to dissolve product. Follow with isotonic saline. Consult a physician. Skin Contact: Wash affected area with soap and water. If irritation persists, consult a physician. Inhalation: Remove to an uncontaminated area, administer oxygen if necessary. If victim has stopped breathing begin CPR. Get medical attention. Ingestion: If conscious, give large quantities of water. Do not induce vomiting.

MEDICAL CONDITIONS PRONE TO AGGRAVATION BY

EXPOSURE: None known

PRIMARY ROUTES OF ENTRY: Inhalation, skin and eye contact.

HEALTH HAZARDS (acute and chronic) / EFFECTS OF OVEREXPOSURE:

1. Eye contact with this material causes irritation and possible damage unless prompt first aid measures area taken.

2. Prolonged or repeated skin contact with this material can cause irritation, redness or rash due to the alkaline nature of this product.

3. Ingestion of this product is expected to cause gastrointestinal irritation.

4. Excessive inhalation of product vapors may cause mucous membrane irritation due to the presence of diethylethanolamine. Inhalation of particle mists from spraying or atomizing the product may be irritating to the upper respiratory tract.

STABILITY: Stable

HAZARDOUS POLYMERIZATION: Will not occur.

HAZARDOUS DECOMPOSITION PRODUCTS: Oxides of carbon, nitrogen and sulfur.

INCOMPATIBILITY: Strong oxidizing agents, alkalis/bases.

CONDITIONS TO AVOID: Contact with incompatible materials.

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Absorb on sweeping compound or other absorbent material. Place in closed container for disposal.

WASTE DISPOSAL: Incinerate or dispose of in accordance with existing Federal, State and Local environmental regulations.

RESPIRATORY PROTECTION: A NIOSH/OSHA approved respirator for product vapors when used in a confined area. If product is sprayed, use a combination vapor-dust/mist or dust/mist respirator.

PROTECTIVE GLOVES: Chemical resistant rubber or plastic.

EYE PROTECTION: Chemical splash goggles.

OTHER PROTECTIVE EQUIPMENT: Eye wash station.

PRECAUTIONS TO BE TAKEN IN HANDLING: Avoid eye and prolonged skin contact. Use in a well ventilated environment.

PRECAUTIONS TO BE TAKEN IN STORING: Keep containers tightly closed.

DOT/IMDG/IATA SHIPPING NAME: N.A.

UN/NA NUMBER: N.A.

DOT/IMDG/IATA HAZARD CLASS.: N.A.

T.S.C.A. STATUS: Listed

DOT/IMDG/IATA REQUIRED LABELS: N.A.

TECHNICAL SHIPPING NAME: N.A.

PREPARED BY: Alla Furman, Senior Corrosion Engineer

APPROVED BY: Christophe Chandler, Lab Director

DATE PREPARED: 8/3/00 SUPERSEDES: 1/20/98

DISCLAIMER: This information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of the Cortec Corporation. The data on this sheet relates only to the specific material designated herein. The Cortec Corporation assumes no legal responsibility for use or reliance upon this data.

N.E. = NOT ESTABLISHED N.A. = NOT APPLICABLE